● NSE 5 - FortiSwitch 7.2 Administrator Exam Materials
Please note that the exam "NSE 5 - FortiSwitch 7.2 Administrator" is no longer offered by Fortinet and is not available for booking through Pearson VUE, so we opened it on free view,
It has been replaced by the exam "NSE 5 - FortiSwitch 7.6 Administrator t"
The new exam version is available on Brave-Dumps and can be purchased.
It has been replaced by the exam "NSE 5 - FortiSwitch 7.6 Administrator t"
The new exam version is available on Brave-Dumps and can be purchased.
Question #31
Question #32
Refer to the configuration:
Which two conditions does FortiSwitch need to meet successfully configure the options shown in the exhibit above?
(Choose two answers)
- A. The FortiSwitch model is equipped with a maximum of 54 interfaces.
- B. FortiSwitch would need to be rebooted.
- C. The split port can be assigned to a native VLAN.
- D. The port full speed prior to the split was 100G QSFP+.
Question #33
What feature can network administrators use to segment network operations and the administration of managed FortiSwitch devices on FortiGate? (Choose one answer)
- A. FortiGate multi-tenancy
- B. Multi-chassis links aggregation trunk
- C. FortiGate clustering protocol
- D. FortiLink split interface
Question #34
Which two types of Layer 3 interfaces can participate in dynamic routing on FortiSwitch? (Choose two answers)
- A. Detected management interfaces
- B. Loopback interfaces
- C. Switch virtual interfaces
- D. Physical interfaces
Question #35
Which drop policy mode, if assigned to a congested port, will drop incoming packets until there is no congestion on the egress port? (Choose one answer)
- A. Tail-drop mode
- B. Weighted round robin mode
- C. Random early detection mode
- D. Strict mode
Question #36
Which packet capture method allows FortiSwitch to capture traffic on trunks and management interfaces? (Choose one answer)
- A. SPAN
- B. Sniffer profile
- C. sFlow
- D. TCP dump
Question #37
Which interfaces on FortiSwitch send out FortiLink discovery frames by default in order to detect a FortiGate with an enabled FortiLink interface? (Choose one answer)
- A. All ports have auto-discovery enabled by default
- B. No ports are enabled by default for auto-discovery. This must be configured under config switch interface.
- C. The ports with auto-discovery enabled by default are dependent upon the FortiSwitch model.
- D. The last four switch ports on FortiSwitch have auto-discovery by default.
Question #38
Refer to the exhibits.
You are asked to ensure that managed FortiSwitch devices are reachable by other devices, such as SNMP and other management tools across your network.
Which setting must you configure to ensure traffic from other devices in the network reaches FortiSwitch?
(Choose one answer)
- A. Select a specific default gateway provided to FortiSwitch as an upstream device.
- B. Change the FortiLink interface IP address and DHCP server address range.
- C. Recreate the FortiLink interface with a nonaggregate setting.
- D. Enable NAC settings to select the onboarding VLAN.
Question #39
How is traffic routed on FortiSwitch? (Choose one answer)
- A. ASIC hardware routing can only handle dynamic routing, if supported.
- B. Layer 3 routing can be configured on FortiSwitch, while managed by FortiGate.
- C. FortiSwitch looks up the hardware routing table and then the forwarding information base (FIB).
- D. Hardware-based routing on FortiSwitch is handled by the CPU.
Question #40
What type of multimode transceiver can be used to split a 40G port? (Choose one answer)
- A. QSFP transceiver
- B. QSFP+ transceiver
- C. SFP+ transceiver
- D. SFP transceiver
Which statement about the IGMP snooping querier when enabled on a VLAN is true? (Choose one answer)