● Securing Networks with Cisco Firepower (300-710 SNCF) Exam Materials
- Less than 260 Verified Questions for Securing Networks with Cisco Firepower Dump (300-710 SNCF Dump)
- Over 3 Students Passed Securing Networks with Cisco Firepower Exam (300-710 SNCF Exam) Using This Dump – Join Them Today!
- 100% Score in Securing Networks with Cisco Firepower Exam (300-710 SNCF Exam) at the Pearson VUE Testing Center
- Over 3 Students Passed Securing Networks with Cisco Firepower Exam (300-710 SNCF Exam) Using This Dump – Join Them Today!
- 100% Score in Securing Networks with Cisco Firepower Exam (300-710 SNCF Exam) at the Pearson VUE Testing Center
Question #1
Question #2
An engineer is configuring a Cisco Secure Firewall Threat Defense device to operate in transparent mode between two switch stacks. VLAN 10 is used for in-band management on both switch stacks. Which two actions are required on the device to inspect traffic between the two switch stacks without causing any interruption to network traffic? (Choose two answers)
- A. Configure at least one bridge group.
- B. Set the MTU to 9198 on all interfaces to support jumbo frames.
- C. Add separate routes for data and management traffic.
- D. Exempt BPDUs from advanced inspection.
- E. Configure a BVI interface for VLAN 10.
Question #3
Refer to the exhibit. The client at IP address 10.204.51.117 cannot reach a website at IP address 10.10.1.1. Which action must be taken by the assigned engineer to resolve the issue? (Choose one answer)
- A. Configure the outside interface to receive SYN-ACK messages.
- B. Configure the inside interface to send ACK messages.
- C. Add a firewall rule to allow the web server to communicate with the DMZ.
- D. Add a firewall rule to allow ACK responses from the inside to the outside.
Question #4
Encrypted Visibility Engine (EVE) is enabled under which tab on an access control policy in Cisco Secure Firewall Management Center? (Choose one answer)
- A. Security Intelligence
- B. Advanced
- C. Network Analysis Policy
- D. SSL
Question #5
What is an attribute of the risk reporting capability in Cisco Secure Firewall Management Center? (Choose one answer)
- A. uses the same templates available to standard reports
- B. includes all domains in a multidomain system
- C. includes the current domain in a multidomain system
- D. uses the XML format to export all reporting
Question #6
An engineer must configure a SPAN to monitor traffic by using a Cisco Secure IPS device in passive mode. The Cisco Secure IPS interface Gi0/1 is connected to Cisco Catalyst Switch Interface Gi0/3. Which SPAN configuration meets the requirement? (Choose one answer)
- A. Switch> enable
Switch# configure terminal
Switch(config)# monitor source interface Gi0/1
Switch(config)# monitor destination interface Gi0/3
Switch(config)# end - B. Switch> enable
Switch# configure terminal
Switch(config)# monitor session 1 source interface Gi0/1
Switch(config)# monitor session 1 destination interface Gi0/3
Switch(config)# end - C. Switch> enable
Switch# configure terminal
Switch(config)# monitor session 1 source interface Gi0/3
Switch(config)# monitor session 1 destination interface Gi0/3
Switch(config)# end - D. Switch> enable
Switch# configure terminal
Switch(config)# monitor source interface Gi0/1
Switch(config)# monitor destination interface Gi0/1
Switch(config)# end
Question #7
The network engineer at an organization must provide a high-level statistics summary about the Cisco Secure Firewall Threat Defense device. The organization is approaching its peak season, so network downtime must be minimized. Which type of report must the network engineer use? (Choose one answer)
- A. host
- B. SNMP
- C. risk
- D. malware
Question #8
A network administrator is configuring a transparent Cisco Secure Firewall Threat Defense registered to a Cisco Secure Firewall Management Center. The administrator wants to configure the Secure Firewall Threat Defense to allow ARP traffic to pass between two interfaces of a bridge group. What must be configured? (Choose one answer)
- A. Use the default configuration on the devices.
- B. An access policy must allow MAC address 0100.0CCC.CCCD.
- C. An access policy must allow MAC address FFFF.FFFF.FFFF.
- D. ARP inspection must be disabled.
Question #9
Refer to the exhibit. An administrator is looking at some of the reporting capabilities for Cisco Secure Firewall and noticed this section of the Network Risk Report showing a lot of SSL activity that could be used for evasion. Which action will mitigate the risk? (Choose one answer)
- A. Use Cisco Secure Endpoint to block all SSL connection.
- B. Use encrypted traffic analytics to detect attacks.
- C. Use SSL decryption to analyze the packets.
- D. Use Cisco Secure Workload to track SSL connection to servers.
Question #10
A network administrator configured an access policy named WEB05401_SRV44120_ALLOW that allows any source from the Internet to reach the public IP address of the web server on port 8080. The administrator also configured a NAT policy that translates a public IP address to an internal web server IP address. Upon testing, the web server is not reachable from the internet on port 8080. Which configuration must the administrator apply to resolve the issue? (Choose one answer)
- A. modify NAT policy to translate the source IP address as well as the destination IP address
- B. configure access policy rule with the action trust
- C. replace public IP address of Web Server to the internal IP address in the access policy
- D. disable the intrusion policy port 8080
An engineer is deploying a Cisco ASA Secure Firewall module. The engineer must be able to examine traffic without impacting the network, and the ASA has been deployed with a single context. Which ASA Secure Firewall module deployment mode must be implemented to meet the requirements? (Choose one answer)